Apache HTTP Server Version 2.2
This document describes when and how to use name-based virtual hosts.
IP-based virtual hosts use the IP address of the connection to determine the correct virtual host to serve. Therefore you need to have a separate IP address for each host. With name-based virtual hosting, the server relies on the client to report the hostname as part of the HTTP headers. Using this technique, many different hosts can share the same IP address.
Name-based virtual hosting is usually simpler, since you need only configure your DNS server to map each hostname to the correct IP address and then configure the Apache HTTP Server to recognize the different hostnames. Name-based virtual hosting also eases the demand for scarce IP addresses. Therefore you should use name-based virtual hosting unless there is a specific reason to choose IP-based virtual hosting. Some reasons why you might consider using IP-based virtual hosting:
|Related Modules||Related Directives|
To use name-based virtual hosting, you must designate the IP
address (and possibly port) on the server that will be accepting
requests for the hosts. This is configured using the
In the normal case where any and all IP addresses on the server should
be used, you can use
* as the argument to
NameVirtualHost. If you're planning to use
multiple ports (e.g. running SSL) you should add a Port to the argument,
*:80. Note that mentioning an IP address in a
NameVirtualHost directive does not
automatically make the server listen to that IP address. See
Setting which addresses and ports Apache uses
for more details. In addition, any IP address specified here must be
associated with a network interface on the server.
The next step is to create a
<VirtualHost> block for
each different host that you would like to serve. The argument to the
must match a defined
NameVirtualHost directive. (In this usual case,
this will be "*:80"). Inside each
<VirtualHost> block, you will need at minimum a
ServerName directive to designate
which host is served and a
directive to show where in the filesystem the content for that host
If you are adding virtual hosts to an existing web server, you
must also create a
<VirtualHost> block for the existing host. The
DocumentRoot included in this virtual host should be the
same as the global
DocumentRoot. List this virtual
host first in the configuration file so that it will act as the default
For example, suppose that you are serving the domain
www.domain.tld and you wish to add the virtual host
www.otherdomain.tld, which points at the same IP address.
Then you simply add the following to
ServerAlias domain.tld *.domain.tld
You can alternatively specify an explicit IP address in place of the
* in both the
<VirtualHost> directives. For example, you might want to do this
in order to run some name-based virtual hosts on one IP address, and either
IP-based, or another set of name-based virtual hosts on another address.
Many servers want to be accessible by more than one name. This is
possible with the
directive, placed inside the
<VirtualHost> section. For example in the first
<VirtualHost> block above, the
ServerAlias directive indicates that
the listed names are other names which people can use to see that same
ServerAlias domain.tld *.domain.tld
then requests for all hosts in the
domain.tld domain will
be served by the
www.domain.tld virtual host. The wildcard
? can be used to match names.
Of course, you can't just make up names and place them in
ServerAlias. You must
first have your DNS server properly configured to map those names to an IP
address associated with your server.
Finally, you can fine-tune the configuration of the virtual hosts
by placing other directives inside the
<VirtualHost> containers. Most directives can be
placed in these containers and will then change the configuration only of
the relevant virtual host. To find out if a particular directive is allowed,
check the Context of the
directive. Configuration directives set in the main server context
container) will be used only if they are not overridden by the virtual host
Now when a request arrives, the server will first check if it is using
an IP address that matches the
NameVirtualHost. If it is, then it will look at each
<VirtualHost> section with a matching
IP address and try to find one where the
ServerAlias matches the requested
hostname. If it finds one, then it uses the configuration for that server.
If no matching virtual host is found, then the first listed virtual
host that matches the IP address will be used.
As a consequence, the first listed virtual host is the default
virtual host. The
the main server will never be used when an IP
address matches the
directive. If you would like to have a special configuration for requests
that do not match any particular virtual host, simply put that configuration
container and list it first in the configuration file.
As mentioned earlier, there are some clients who do not send the required data for the name-based virtual hosts to work properly. These clients will always be sent the pages from the first virtual host listed for that IP address (the primary name-based virtual host).
Please note that when we say older, we really do mean older. You are
very unlikely to encounter one of these browsers in use today. All
current versions of any browser send the
Host header as
required for name-based virtual hosts.
There is a possible workaround with the
directive, albeit a slightly cumbersome one:
What does this mean? It means that a request for any URI
beginning with "
/domain" will be served from the
www.domain.tld. This means that the
pages can be accessed as
for all clients, although clients sending a
can also access it as
In order to make this work, put a link on your primary
virtual host's page to
http://www.domain.tld/domain/. Then, in the virtual
host's pages, be sure to use either purely relative links
../icons/image.gif") or links containing the
This requires a bit of discipline, but adherence to these guidelines will, for the most part, ensure that your pages will work with all browsers, new and old.